# Copyright 2024 The HuggingFace Inc. team. All rights reserved.
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
#     http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
"""Mocked classes and functions from dynamixel_sdk to allow for continuous integration
and testing code logic that requires hardware and devices (e.g. robot arms, cameras)

Warning: These mocked versions are minimalist. They do not exactly mock every behaviors
from the original classes and functions (e.g. return types might be None instead of boolean).
"""

# from dynamixel_sdk import COMM_SUCCESS

DEFAULT_BAUDRATE = 9_600
COMM_SUCCESS = 0  # tx or rx packet communication success


def convert_to_bytes(value, _byte):
    # TODO(rcadene): remove need to mock `convert_to_bytes` by implemented the inverse transform
    # `convert_bytes_to_value`
    return value


def get_default_motor_values(motor_index):
    return {
        # Key (int) are from X_SERIES_CONTROL_TABLE
        7: motor_index,  # ID
        8: DEFAULT_BAUDRATE,  # Baud_rate
        10: 0,  # Drive_Mode
        64: 0,  # Torque_Enable
        # Set 2560 since calibration values for Aloha gripper is between start_pos=2499 and end_pos=3144
        # For other joints, 2560 will be autocorrected to be in calibration range
        132: 2560,  # Present_Position
    }


class PortHandler:
    def __init__(self, port):
        self.port = port
        # factory default baudrate
        self.baudrate = DEFAULT_BAUDRATE

    def openPort(self):  # noqa: N802
        return True

    def closePort(self):  # noqa: N802
        pass

    def setPacketTimeoutMillis(self, timeout_ms):  # noqa: N802
        del timeout_ms  # unused

    def getBaudRate(self):  # noqa: N802
        return self.baudrate

    def setBaudRate(self, baudrate):  # noqa: N802
        self.baudrate = baudrate


class PacketHandler:
    def __init__(self, protocol_version):
        del protocol_version  # unused
        # Use packet_handler.data to communicate across Read and Write
        self.data = {}


class GroupSyncRead:
    def __init__(self, _port_handler, packet_handler, _address, _byte):
        self.packet_handler = packet_handler

    def addParam(self, motor_index):  # noqa: N802
        # Initialize motor default values
        if motor_index not in self.packet_handler.data:
            self.packet_handler.data[motor_index] = get_default_motor_values(motor_index)

    def txRxPacket(self):  # noqa: N802
        return COMM_SUCCESS

    def getData(self, index, address, _byte):  # noqa: N802
        return self.packet_handler.data[index][address]


class GroupSyncWrite:
    def __init__(self, _port_handler, packet_handler, address, _byte):
        self.packet_handler = packet_handler
        self.address = address

    def addParam(self, index, data):  # noqa: N802
        # Initialize motor default values
        if index not in self.packet_handler.data:
            self.packet_handler.data[index] = get_default_motor_values(index)
        self.changeParam(index, data)

    def txPacket(self):  # noqa: N802
        return COMM_SUCCESS

    def changeParam(self, index, data):  # noqa: N802
        self.packet_handler.data[index][self.address] = data